The function may be called by the names: c05qbc, nag_roots_sys_func_easy or nag_zero_nonlin_eqns_easy.
The system of equations is defined as:
c05qbc is based on the MINPACK routine HYBRD1 (see Moré et al. (1980)). It chooses the correction at each step as a convex combination of the Newton and scaled gradient directions. The Jacobian is updated by the rank-1 method of Broyden. At the starting point, the Jacobian is approximated by forward differences, but these are not used again until the rank-1 method fails to produce satisfactory progress. For more details see Powell (1970).
Moré J J, Garbow B S and Hillstrom K E (1980) User guide for MINPACK-1 Technical Report ANL-80-74 Argonne National Laboratory
Powell M J D (1970) A hybrid method for nonlinear algebraic equations Numerical Methods for Nonlinear Algebraic Equations (ed P Rabinowitz) Gordon and Breach
1: – function, supplied by the userExternal Function
fcn must return the values of the functions at a point .
On entry: the components of the point at which the functions must be evaluated.
3: – doubleOutput
On exit: the function values .
4: – Nag_Comm *
Pointer to structure of type Nag_Comm; the following members are relevant to fcn.
user – double *
iuser – Integer *
p – Pointer
The type Pointer will be void *. Before calling c05qbc you may allocate memory and initialize these pointers with various quantities for use by fcn when called from c05qbc (see Section 3.1.1 in the Introduction to the NAG Library CL Interface).
5: – Integer *Input/Output
On entry: .
On exit: in general, iflag should not be reset by fcn. If, however, you wish to terminate execution (perhaps because some illegal point x has been reached), iflag should be set to a negative integer.
Note:fcn should not return floating-point NaN (Not a Number) or infinity values, since these are not handled by c05qbc. If your code inadvertently does return any NaNs or infinities, c05qbc is likely to produce unexpected results.
2: – IntegerInput
On entry: , the number of equations.
3: – doubleInput/Output
On entry: an initial guess at the solution vector.
On exit: the final estimate of the solution vector.
4: – doubleOutput
On exit: the function values at the final point returned in x.
5: – doubleInput
On entry: the accuracy in x to which the solution is required.
, where is the machine precision returned by X02AJC.
6: – Nag_Comm *
The NAG communication argument (see Section 3.1.1 in the Introduction to the NAG Library CL Interface).
7: – NagError *Input/Output
The NAG error argument (see Section 7 in the Introduction to the NAG Library CL Interface).
6Error Indicators and Warnings
Dynamic memory allocation failed.
See Section 3.1.2 in the Introduction to the NAG Library CL Interface for further information.
On entry, argument had an illegal value.
On entry, .
An internal error has occurred in this function. Check the function call and any array sizes. If the call is correct then please contact NAG for assistance.
See Section 7.5 in the Introduction to the NAG Library CL Interface for further information.
The iteration is not making good progress. This failure exit may indicate that the system does not have a zero, or that the solution is very close to the origin (see Section 7). Otherwise, rerunning c05qbc from a different starting point may avoid the region of difficulty.
Your licence key may have expired or may not have been installed correctly.
See Section 8 in the Introduction to the NAG Library CL Interface for further information.
On entry, .
There have been at least calls to fcn. Consider restarting the calculation from the point held in x.
No further improvement in the solution is possible. xtol is too small: .
If is the true solution, c05qbc tries to ensure that
If this condition is satisfied with , then the larger components of have significant decimal digits. There is a danger that the smaller components of may have large relative errors, but the fast rate of convergence of c05qbc usually obviates this possibility.
If xtol is less than machine precision and the above test is satisfied with the machine precision in place of xtol, then the function exits with NE_TOO_SMALL.
Note: this convergence test is based purely on relative error, and may not indicate convergence if the solution is very close to the origin.
The convergence test assumes that the functions are reasonably well behaved. If this condition is not satisfied, then c05qbc may incorrectly indicate convergence. The validity of the answer can be checked, for example, by rerunning c05qbc with a lower value for xtol.
8Parallelism and Performance
Background information to multithreading can be found in the Multithreading documentation.
c05qbc is threaded by NAG for parallel execution in multithreaded implementations of the NAG Library.
c05qbc makes calls to BLAS and/or LAPACK routines, which may be threaded within the vendor library used by this implementation. Consult the documentation for the vendor library for further information.
Please consult the X06 Chapter Introduction for information on how to control and interrogate the OpenMP environment used within this function. Please also consult the Users' Note for your implementation for any additional implementation-specific information.
Local workspace arrays of fixed lengths are allocated internally by c05qbc. The total size of these arrays amounts to double elements.
The time required by c05qbc to solve a given problem depends on , the behaviour of the functions, the accuracy requested and the starting point. The number of arithmetic operations executed by c05qbc to process each evaluation of the functions is approximately . The timing of c05qbc is strongly influenced by the time spent evaluating the functions.
Ideally the problem should be scaled so that, at the solution, the function values are of comparable magnitude.
This example determines the values which satisfy the tridiagonal equations: