) of a function at a point with respect to a single variable. A corresponding set of error estimates is also returned. Derivatives are calculated using an extension of the Neville algorithm. This routine differs from d04aaf, in that the abscissae and corresponding function values must be calculated before this routine is called. The abscissae may be generated using d04bbf.

2 Specification

Fortran Interface

Subroutine d04baf (

xval, fval, der, erest, ifail)

Integer, Intent (Inout)	::	ifail
Real (Kind=nag_wp), Intent (In)	::	xval(21), fval(21)
Real (Kind=nag_wp), Intent (Out)	::	der(14), erest(14)

C Header Interface

#include <nag.h>

void	d04baf_ (const double xval[], const double fval[], double der[], double erest[], Integer *ifail)

The routine may be called by the names d04baf or nagf_numdiff_rcomm.

3 Description

d04baf provides a set of approximations:

der (j), j = 1, 2, \dots, 14

to the derivatives:

f^{(j)} (x_{0}), j = 1, 2, \dots, 14

of a real valued function

f (x)

at a real abscissa

x_{0}

, together with a set of error estimates:

erest (j), j = 1, 2, \dots, 14

which hopefully satisfy:

| der (j) - f^{(j)} (x_{0}) | < erest (j), j = 1, 2, \dots, 14 .

The results

der (j)

and

erest (j)

are based on

21

function values:

f (x_{0}), f (x_{0} \pm (2 i - 1) h), i = 1, 2, \dots, 10 .

The abscissae

x

and the corresponding function values

f (x)

should be passed into d04baf as the vectors xval and fval respectively. The step size

h

is derived from the abscissae in xval. See Section 9 for a discussion of how the derived value of

h

may affect the results of d04baf. The order in which the abscissae and function values are stored in xval and fval is irrelevant, provided that the function value at any given index corresponds to the value of the abscissa at the same index. Abscissae may be automatically generated using d04bbf if desired. For each derivative d04baf employs an extension of the Neville Algorithm (see Lyness and Moler (1969)) to obtain a selection of approximations.

For example, for odd derivatives, this routine calculates a set of numbers:

T_{k, p, s}, p = s, s + 1, \dots, 6, k = 0, 1, \dots, 9 - p

each of which is an approximation to

f^{(2 s + 1)} (x_{0}) / (2 s + 1)!

. A specific approximation

T_{k, p, s}

is of polynomial degree

2 p + 2

and is based on polynomial interpolation using function values

f (x_{0} \pm (2 i - 1) h)

, for

k = k, \dots, k + p

. In the absence of round-off error, the better approximations would be associated with the larger values of

p

and of

k

. However, round-off error in function values has an increasingly contaminating effect for successively larger values of

p

. This routine proceeds to make a judicious choice between all the approximations in the following way.

For a specified value of

s

, let:

R_{p} = U_{p} - L_{p}, p = s, s + 1, \dots, 6

where

U_{p} = \max_{k} (T_{k, p, s})

and

L_{p} = \min_{k} (T_{k, p, s})

, for

k = 0, 1, \dots, 9 - p

, and let

\bar{p}

be such that

R_{\bar{p}} = \min_{p} (R_{p})

, for

p = s, \dots, 6

This routine returns:

der (2 s + 1) = \frac{1}{8 - \bar{p}} \times {\sum_{k = 0}^{9 - \bar{p}} T_{k, \bar{p}, s} - U_{\bar{p}} - L_{\bar{p}}} (2 s + 1)!

and

erest (2 s + 1) = R_{\bar{p}} \times (2 s + 1)! \times K_{2 s + 1}

where

K_{j}

is a safety factor which has been assigned the values:

$K_{j} = 1$ ,	$j \leq 9$
$K_{j} = 1.5$ ,	$j = 10, 11$
$K_{j} = 2$	$j \geq 12$ ,

on the basis of performance statistics.

The even order derivatives are calculated in a precisely analogous manner.

4 References

Lyness J N and Moler C B (1969) Generalised Romberg methods for integrals of derivatives Numer. Math. 14 1–14

5 Arguments

1: $xval (21)$ – Real (Kind=nag_wp) array Input: On entry: the abscissae at which the function has been evaluated, as described in Section 3. These can be generated by calling d04bbf. The order of the abscissae is irrelevant.

Constraint: the values in xval must span the set ${x_{0}, x_{0} \pm (2 j - 1) h}$ , for $j = 1, 2, \dots, 10$ .
2: $fval (21)$ – Real (Kind=nag_wp) array Input: On entry: $fval (j)$ must contain the function value at $xval (j)$ , for $j = 1, 2, \dots, 21$ .
3: $der (14)$ – Real (Kind=nag_wp) array Output: On exit: the $14$ derivative estimates.
4: $erest (14)$ – Real (Kind=nag_wp) array Output: On exit: the $14$ error estimates for the derivatives.
5: $ifail$ – Integer Input/Output: On entry: ifail must be set to $0$ , $−1$ or $1$ to set behaviour on detection of an error; these values have no effect when no error is detected.
A value of $0$ causes the printing of an error message and program execution will be halted; otherwise program execution continues. A value of $−1$ means that an error message is printed while a value of $1$ means that it is not.

If halting is not appropriate, the value $−1$ or $1$ is recommended. If message printing is undesirable, then the value $1$ is recommended. Otherwise, the value $0$ is recommended. When the value $- 1$ or $1$ is used it is essential to test the value of ifail on exit.

On exit: $ifail = 0$ unless the routine detects an error or a warning has been flagged (see Section 6).

6 Error Indicators and Warnings

If on entry

ifail = 0

−1

, explanatory error messages are output on the current error message unit (as defined by x04aaf).

Errors or warnings detected by the routine:

$ifail = 1$: On entry, the values of xval are not correctly spaced.
Derived $h = ⟨ value ⟩$ .

The derived $h$ is below tolerance.
Derived $h > ⟨ value ⟩$ is required. Derived $h = ⟨ value ⟩$ .

$ifail = - 99$: An unexpected error has been triggered by this routine. Please contact NAG.
See Section 7 in the Introduction to the NAG Library FL Interface for further information.

$ifail = - 399$: Your licence key may have expired or may not have been installed correctly.
See Section 8 in the Introduction to the NAG Library FL Interface for further information.

$ifail = - 999$: Dynamic memory allocation failed.
See Section 9 in the Introduction to the NAG Library FL Interface for further information.

7 Accuracy

The accuracy of the results is problem dependent. An estimate of the accuracy of each result

der (j)

is returned in

erest (j)

(see Sections 3, 5 and 9).

A basic feature of any floating-point routine for numerical differentiation based on real function values on the real axis is that successively higher order derivative approximations are successively less accurate. It is expected that in most cases

der (14)

will be unusable. As an aid to this process, the sign of

erest (j)

is set negative when the estimated absolute error is greater than the approximate derivative itself, i.e., when the approximate derivative may be so inaccurate that it may even have the wrong sign. It is also set negative in some other cases when information available to d04baf indicates that the corresponding value of

der (j)

is questionable.

The actual values in erest depend on the accuracy of the function values, the properties of the machine arithmetic, the analytic properties of the function being differentiated and the step length

h

(see Section 9). The only hard and fast rule is that for a given objective function and

h

, the values of

erest (j)

increase with increasing

j

. The limit of

14

is dictated by experience. Only very rarely can one obtain meaningful approximations for higher order derivatives on conventional machines.

8 Parallelism and Performance

Background information to multithreading can be found in the Multithreading documentation.

d04baf is not threaded in any implementation.

9 Further Comments

The results depend very critically on the choice of the step length

h

. The overall accuracy is diminished as

h

becomes small (because of the effect of round-off error) and as

h

becomes large (because the discretization error also becomes large). If this routine is used four or five times with different values of

h

one can find a reasonably good value. A process in which the value of

h

is successively halved (or doubled) is usually quite effective. Experience has shown that in cases in which the Taylor series for the objective function about

x_{0}

has a finite radius of convergence

R

, the choices of

h > R / 19

are not likely to lead to good results. In this case some function values lie outside the circle of convergence.

As mentioned, the order of the abscissae in xval does not matter, provided the corresponding values of fval are ordered identically. If the abscissae are generated by d04bbf, then they will be in ascending order. In particular, the target abscissa