The function may be called by the names: s17dec, nag_specfun_bessel_j_complex or nag_complex_bessel_j.
3Description
s17dec evaluates a sequence of values for the Bessel function , where is complex, , and is the real, non-negative order. The -member sequence is generated for orders , . Optionally, the sequence is scaled by the factor .
Note: although the function may not be called with less than zero, for negative orders the formula may be used (for the Bessel function , see s17dcc).
The function is derived from the function CBESJ in Amos (1986). It is based on the relations , , and , .
The Bessel function is computed using a variety of techniques depending on the region under consideration.
When is greater than , extra values of are computed using recurrence relations.
For very large or , argument reduction will cause total loss of accuracy, and so no computation is performed. For slightly smaller or , the computation is performed but results are accurate to less than half of machine precision. If is large, there is a risk of overflow and so no computation is performed. In all the above cases, a warning is given by the function.
Amos D E (1986) Algorithm 644: A portable package for Bessel functions of a complex argument and non-negative order ACM Trans. Math. Software12 265–273
5Arguments
1: – doubleInput
On entry: , the order of the first member of the sequence of functions.
Constraint:
.
2: – ComplexInput
On entry: the argument of the functions.
3: – IntegerInput
On entry: , the number of members required in the sequence .
Constraint:
.
4: – Nag_ScaleResTypeInput
On entry: the scaling option.
The results are returned unscaled.
The results are returned scaled by the factor .
Constraint:
or .
5: – ComplexOutput
On exit: the required function values: contains
, for .
6: – Integer *Output
On exit: the number of components of cy that are set to zero due to underflow. If , then elements , are set to zero.
7: – NagError *Input/Output
The NAG error argument (see Section 7 in the Introduction to the NAG Library CL Interface).
6Error Indicators and Warnings
NE_ALLOC_FAIL
Dynamic memory allocation failed.
See Section 3.1.2 in the Introduction to the NAG Library CL Interface for further information.
NE_BAD_PARAM
On entry, argument had an illegal value.
NE_INT
On entry, .
Constraint: .
NE_INTERNAL_ERROR
An internal error has occurred in this function. Check the function call and any array sizes. If the call is correct then please contact NAG for assistance.
See Section 7.5 in the Introduction to the NAG Library CL Interface for further information.
NE_NO_LICENCE
Your licence key may have expired or may not have been installed correctly.
See Section 8 in the Introduction to the NAG Library CL Interface for further information.
NE_OVERFLOW_LIKELY
No computation because , .
NE_REAL
On entry, .
Constraint: .
NE_TERMINATION_FAILURE
No computation – algorithm termination condition not met.
NE_TOTAL_PRECISION_LOSS
No computation because .
No computation because .
NW_SOME_PRECISION_LOSS
Results lack precision because .
Results lack precision because .
7Accuracy
All constants in s17dec are given to approximately digits of precision. Calling the number of digits of precision in the floating-point arithmetic being used , then clearly the maximum number of correct digits in the results obtained is limited by . Because of errors in argument reduction when computing elementary functions inside s17dec, the actual number of correct digits is limited, in general, by , where represents the number of digits lost due to the argument reduction. Thus the larger the values of and , the less the precision in the result. If s17dec is called with , then computation of function values via recurrence may lead to some further small loss of accuracy.
If function values which should nominally be identical are computed by calls to s17dec with different base values of and different , the computed values may not agree exactly. Empirical tests with modest values of and have shown that the discrepancy is limited to the least significant – digits of precision.
8Parallelism and Performance
Background information to multithreading can be found in the Multithreading documentation.
s17dec is not threaded in any implementation.
9Further Comments
The time taken for a call of s17dec is approximately proportional to the value of , plus a constant. In general it is much cheaper to call s17dec with greater than , rather than to make separate calls to s17dec.
Paradoxically, for some values of and , it is cheaper to call s17dec with a larger value of than is required, and then discard the extra function values returned. However, it is not possible to state the precise circumstances in which this is likely to occur. It is due to the fact that the base value used to start recurrence may be calculated in different regions for different , and the costs in each region may differ greatly.
Note that if the function required is or , i.e., or , where is real and positive, and only a single unscaled function value is required, then it may be much cheaper to call s17aecors17afc respectively.
10Example
This example prints a caption and then proceeds to read sets of data from the input data stream. The first datum is a value for the order fnu, the second is a complex value for the argument, z, and the third is a character value
used as a flag
to set the argument scal. The program calls the function with to evaluate the function for orders fnu and , and it prints the results. The process is repeated until the end of the input data stream is encountered.