NAG FL Interface
f11gtf (complex_​herm_​basic_​diag)

1 Purpose

f11gtf is the third in a suite of three routines for the iterative solution of a complex Hermitian system of simultaneous linear equations (see Golub and Van Loan (1996)). f11gtf returns information about the computations during an iteration and/or after this has been completed. The first routine of the suite, f11grf, is a setup routine, the second routine, f11gsf is the proper iterative solver.
These three routines are suitable for the solution of large sparse complex Hermitian systems of equations.

2 Specification

Fortran Interface
Subroutine f11gtf ( itn, stplhs, stprhs, anorm, sigmax, its, sigerr, work, lwork, ifail)
Integer, Intent (In) :: lwork
Integer, Intent (Inout) :: ifail
Integer, Intent (Out) :: itn, its
Real (Kind=nag_wp), Intent (Out) :: stplhs, stprhs, anorm, sigmax, sigerr
Complex (Kind=nag_wp), Intent (In) :: work(lwork)
C Header Interface
#include <nag.h>
void  f11gtf_ (Integer *itn, double *stplhs, double *stprhs, double *anorm, double *sigmax, Integer *its, double *sigerr, const Complex work[], const Integer *lwork, Integer *ifail)
The routine may be called by the names f11gtf or nagf_sparse_complex_herm_basic_diag.

3 Description

f11gtf returns information about the solution process. It can be called both during a monitoring step of the solver f11gsf or after this solver has completed its tasks. Calling f11gtf at any other time will result in an error condition being raised.
For further information you should read the documentation for f11grf and f11gsf.

4 References

Golub G H and Van Loan C F (1996) Matrix Computations (3rd Edition) Johns Hopkins University Press, Baltimore

5 Arguments

1: itn Integer Output
On exit: the number of iterations carried out by f11gsf.
2: stplhs Real (Kind=nag_wp) Output
On exit: the current value of the left-hand side of the termination criterion used by f11gsf.
3: stprhs Real (Kind=nag_wp) Output
On exit: the current value of the right-hand side of the termination criterion used by f11gsf.
4: anorm Real (Kind=nag_wp) Output
On exit: the norm A1=A when either it has been supplied to f11grf or it has been estimated by f11gsf (see also Sections 3 and 5 in f11grf).
Otherwise, anorm=0.0 is returned.
5: sigmax Real (Kind=nag_wp) Output
On exit: the current estimate of the largest singular value σ1A¯ of the preconditioned iteration matrix A¯=E-1AE-H, when either it has been supplied to f11grf or it has been estimated by f11gsf (see also Sections 3 and 5 in f11grf). Note that if its<itn then sigmax contains the final estimate. If, on final exit from f11gsf, its=itn, the estimation of σ1A¯ may have not converged: in this case you should look at the value returned in sigerr. Otherwise, sigmax=0.0 is returned.
6: its Integer Output
On exit: the number of iterations employed so far in the computation of the estimate of σ1A¯, the largest singular value of the preconditioned matrix A¯=E-1AE-H, when σ1A¯ has been estimated by f11gsf using the bisection method (see also Sections 3, 5 and 9 in f11grf). Otherwise, its=0 is returned.
7: sigerr Real (Kind=nag_wp) Output
On exit: if σ1A¯ has been estimated by f11gsf using bisection,
sigerr=maxσ1k-σ1k-1σ1k,σ1k-σ1k-2σ1k ,  
where k=its denotes the iteration number. The estimation has converged if sigerrsigtol where sigtol is an input argument to f11grf.
Otherwise, sigerr=0.0 is returned.
8: worklwork Complex (Kind=nag_wp) array Communication Array
On entry: the array work as returned by f11gsf (see also Section 3 in f11gsf).
9: lwork Integer Input
On entry: the dimension of the array work as declared in the (sub)program from which f11gtf is called (see also Section 5 in f11grf).
Constraint: lwork120.
Note:  although the minimum value of lwork ensures the correct functioning of f11gtf, a larger value is required by the iterative solver f11gsf (see also Section 5 in f11grf).
10: ifail Integer Input/Output
On entry: ifail must be set to 0, -1 or 1 to set behaviour on detection of an error; these values have no effect when no error is detected.
A value of 0 causes the printing of an error message and program execution will be halted; otherwise program execution continues. A value of -1 means that an error message is printed while a value of 1 means that it is not.
If halting is not appropriate, the value -1 or 1 is recommended. If message printing is undesirable, then the value 1 is recommended. Otherwise, the value 0 is recommended. When the value -1 or 1 is used it is essential to test the value of ifail on exit.
On exit: ifail=0 unless the routine detects an error or a warning has been flagged (see Section 6).

6 Error Indicators and Warnings

If on entry ifail=0 or -1, explanatory error messages are output on the current error message unit (as defined by x04aaf).
Errors or warnings detected by the routine:
ifail=1
f11gtf has been called out of sequence.
ifail=-9
On entry, lwork=value.
Constraint: lwork120.
ifail=-99
An unexpected error has been triggered by this routine. Please contact NAG.
See Section 7 in the Introduction to the NAG Library FL Interface for further information.
ifail=-399
Your licence key may have expired or may not have been installed correctly.
See Section 8 in the Introduction to the NAG Library FL Interface for further information.
ifail=-999
Dynamic memory allocation failed.
See Section 9 in the Introduction to the NAG Library FL Interface for further information.

7 Accuracy

Not applicable.

8 Parallelism and Performance

f11gtf is not threaded in any implementation.

9 Further Comments

None.

10 Example

See Section 10 in f11grf.