Integer, Intent (In)	::	n, nmod, nterms(nmod)
Integer, Intent (Inout)	::	ifail
Real (Kind=nag_wp), Intent (In)	::	sigsq, tss, rss(nmod)
Real (Kind=nag_wp), Intent (Out)	::	rsq(nmod), cp(nmod)
Character (1), Intent (In)	::	mean

C Header Interface

#include <nag.h>

void	g02ecf_ (const char mean, const Integer n, const double sigsq, const double tss, const Integer nmod, const Integer nterms[], const double rss[], double rsq[], double cp[], Integer ifail, const Charlen length_mean)

The routine may be called by the names g02ecf or nagf_correg_linregm_rssq_stat.

3 Description

When selecting a linear regression model for a set of

n

observations a balance has to be found between the number of independent variables in the model and fit as measured by the residual sum of squares. The more variables included the smaller will be the residual sum of squares. Two statistics can help in selecting the best model.

(a) $R^{2}$ represents the proportion of variation in the dependent variable that is explained by the independent variables.
$R^{2} = \frac{Regression Sum of Squares}{Total Sum of Squares},$

where $Total Sum of Squares = tss = \sum {(y - \bar{y})}^{2}$ (if mean is fitted, otherwise $tss = \sum y^{2}$ ) and

$Regression Sum of Squares = RegSS = tss - rss$ , where
$rss = residual sum of squares = \sum {(y - \hat{y})}^{2}$ .

The $R^{2}$ -values can be examined to find a model with a high $R^{2}$ -value but with small number of independent variables.
(b) $C_{p}$ statistic.
$C_{p} = \frac{rss}{{\hat{σ}}^{2}} - (n - 2 p),$
where $p$ is the number of parameters (including the mean) in the model and ${\hat{σ}}^{2}$ is an estimate of the true variance of the errors. This can often be obtained from fitting the full model.
A well fitting model will have $C_{p} ≃ p$ . $C_{p}$ is often plotted against $p$ to see which models are closest to the $C_{p} = p$ line.

g02ecf may be called after g02eaf which calculates the residual sums of squares for all possible linear regression models.

4 References

Draper N R and Smith H (1985) Applied Regression Analysis (2nd Edition) Wiley

Weisberg S (1985) Applied Linear Regression Wiley

5 Arguments

1: $mean$ – Character(1) Input

On entry: indicates if a mean term is to be included.

$mean ='M'$: A mean term, intercept, will be included in the model.
$mean ='Z'$: The model will pass through the origin, zero-point.

Constraint:

mean ='M'

'Z'

2: $n$ – Integer Input

On entry:

n

, the number of observations used in the regression model.

Constraint:

n

must be greater than

2 \times p_{\max}

, where

p_{\max}

is the largest number of independent variables fitted (including the mean if fitted).

3: $sigsq$ – Real (Kind=nag_wp) Input

On entry: the best estimate of true variance of the errors,

{\hat{σ}}^{2}

Constraint:

sigsq > 0.0

4: $tss$ – Real (Kind=nag_wp) Input

On entry: the total sum of squares for the regression model.

Constraint:

tss > 0.0

5: $nmod$ – Integer Input

On entry: the number of regression models.

Constraint:

nmod > 0

6: $nterms (nmod)$ – Integer array Input

On entry:

nterms (i)

must contain the number of independent variables (not counting the mean) fitted to the

i

th model, for

i = 1, 2, \dots, nmod

7: $rss (nmod)$ – Real (Kind=nag_wp) array Input

On entry:

rss (i)

must contain the residual sum of squares for the

i

th model.

Constraint:

rss (i) \leq tss

, for

i = 1, 2, \dots, nmod

8: $rsq (nmod)$ – Real (Kind=nag_wp) array Output

On exit:

rsq (i)

contains the

R^{2}

-value for the

i

th model, for

i = 1, 2, \dots, nmod

9: $cp (nmod)$ – Real (Kind=nag_wp) array Output

On exit:

cp (i)

contains the

C_{p}

-value for the

i

th model, for

i = 1, 2, \dots, nmod

10: $ifail$ – Integer Input/Output

On entry: ifail must be set to

0

- 1 or 1

. If you are unfamiliar with this argument you should refer to Section 4 in the Introduction to the NAG Library FL Interface for details.

For environments where it might be inappropriate to halt program execution when an error is detected, the value

- 1 or 1

is recommended. If the output of error messages is undesirable, then the value

1

is recommended. Otherwise, if you are not familiar with this argument, the recommended value is

0

. When the value $- 1 or 1$ is used it is essential to test the value of ifail on exit.

On exit:

ifail = 0

unless the routine detects an error or a warning has been flagged (see Section 6).

6 Error Indicators and Warnings

If on entry

ifail = 0

- 1

, explanatory error messages are output on the current error message unit (as defined by x04aaf).

Errors or warnings detected by the routine:

$ifail = 1$: On entry, $mean = 〈value〉$ .
Constraint: $mean ='M'$ or $'Z'$ .

On entry, $nmod = 〈value〉$ .
Constraint: $nmod > 0$ .

On entry, $sigsq = 〈value〉$ .
Constraint: $sigsq > 0.0$ .

On entry, $tss = 〈value〉$ .
Constraint: $tss > 0.0$ .

$ifail = 2$: On entry: the number of parameters, $p$ , is $〈value〉$ and $n = 〈value〉$ .
Constraint: $n \geq 2 p$ .

$ifail = 3$: On entry, $rss (〈value〉) = 〈value〉$ and $tss = 〈value〉$ .
Constraint: $rss (i) \leq tss$ , for all $i$ .

$ifail = 4$: A value of $C_{p}$ is less than $0.0$ . This may occur if sigsq is too large or if rss, n or IP are incorrect.

$ifail = - 99$: An unexpected error has been triggered by this routine. Please contact NAG.
See Section 7 in the Introduction to the NAG Library FL Interface for further information.

$ifail = - 399$: Your licence key may have expired or may not have been installed correctly.
See Section 8 in the Introduction to the NAG Library FL Interface for further information.

$ifail = - 999$: Dynamic memory allocation failed.
See Section 9 in the Introduction to the NAG Library FL Interface for further information.

7 Accuracy

Accuracy is sufficient for all practical purposes.

8 Parallelism and Performance

g02ecf is not threaded in any implementation.

9 Further Comments

None.

10 Example

The data, from an oxygen uptake experiment, is given by Weisberg (1985). The independent and dependent variables are read and the residual sums of squares for all possible models computed using g02eaf. The values of

R^{2}

and

C_{p}

are then computed and printed along with the names of variables in the models.

Interfaces: FL CL AD

NAG FL Interface Introduction

G02 (Correg) Chapter Contents

G02 (Correg) Chapter Introduction

g02ec: FL CL AD

where	$Total Sum of Squares = tss = \sum {(y - \bar{y})}^{2}$ (if mean is fitted, otherwise $tss = \sum y^{2}$ ) and
	$Regression Sum of Squares = RegSS = tss - rss$ , where $rss = residual sum of squares = \sum {(y - \hat{y})}^{2}$ .

NAG FL Interfaceg02ecf (linregm_​rssq_​stat)

▸▿ Contents

1 Purpose

2 Specification

3 Description

4 References

5 Arguments

6 Error Indicators and Warnings

7 Accuracy

8 Parallelism and Performance

9 Further Comments

10 Example

10.1 Program Text

10.2 Program Data

10.3 Program Results

NAG FL Interface
g02ecf (linregm_rssq_stat)