NAG FL Interface
f11btf (complex_​gen_​basic_​diag)

1 Purpose

2 Specification

3 Description

4 References

5 Arguments

1: $\mathbf{itn}$ – Integer Output

On exit: the number of iterations carried out by f11bsf.

2: $\mathbf{stplhs}$ – Real (Kind=nag_wp) Output

On exit: the current value of the left-hand side of the termination criterion used by f11bsf.

3: $\mathbf{stprhs}$ – Real (Kind=nag_wp) Output

On exit: the current value of the right-hand side of the termination criterion used by f11bsf.

4: $\mathbf{anorm}$ – Real (Kind=nag_wp) Output

On exit: if $\mathbf{iterm}=1$ in the previous call to f11brf, then anorm contains ${‖A‖}_p$, where $p=1$, $2$ or $\infty$, either supplied or, in the case of $1$ or $\infty$, estimated by f11bsf; otherwise $\mathbf{anorm}=0.0$.

5: $\mathbf{sigmax}$ – Real (Kind=nag_wp) Output

On exit: if $\mathbf{iterm}=2$ in the previous call to f11brf, the current estimate of the largest singular value ${\sigma }_1\left(\overline{A}\right)$ of the preconditioned iteration matrix when it is used by the termination criterion in f11bsf, either when it has been supplied to f11brf or it has been estimated by f11bsf (see also Sections 3 and 5 in f11brf); otherwise, $\mathbf{sigmax}=0.0$ is returned.

6: $\mathbf{work}\left(\mathbf{lwork}\right)$ – Complex (Kind=nag_wp) array Communication Array

On entry: the array work as returned by f11bsf (see also Sections 3 and 5 in f11bsf).

7: $\mathbf{lwork}$ – Integer Input

On entry: the dimension of the array work as declared in the (sub)program from which f11btf is called (see also f11brf).

Constraint: $\mathbf{lwork}\ge 120$.

Note:  although the minimum value of lwork ensures the correct functioning of f11btf, a larger value is required by the iterative solver f11bsf (see also f11brf).

8: $\mathbf{ifail}$ – Integer Input/Output

On entry: ifail must be set to $0$, $-1\text{ or }1$. If you are unfamiliar with this argument you should refer to Section 4 in the Introduction to the NAG Library FL Interface for details.

For environments where it might be inappropriate to halt program execution when an error is detected, the value $-1\text{ or }1$ is recommended. If the output of error messages is undesirable, then the value $1$ is recommended. Otherwise, if you are not familiar with this argument, the recommended value is $0$. When the value $-\mathbf{1}\text{ or }\mathbf{1}$ is used it is essential to test the value of ifail on exit.

On exit: $\mathbf{ifail}=\mathbf{0}$ unless the routine detects an error or a warning has been flagged (see Section 6).

6 Error Indicators and Warnings

$\mathbf{ifail}=1$

f11btf has been called out of sequence.

$\mathbf{ifail}=-7$

On entry, $\mathbf{lwork}=〈\mathit{\text{value}}〉$.
Constraint: $\mathbf{lwork}\ge 120$.

$\mathbf{ifail}=-99$

An unexpected error has been triggered by this routine. Please contact NAG.

See Section 7 in the Introduction to the NAG Library FL Interface for further information.

$\mathbf{ifail}=-399$

Your licence key may have expired or may not have been installed correctly.

See Section 8 in the Introduction to the NAG Library FL Interface for further information.

$\mathbf{ifail}=-999$

Dynamic memory allocation failed.

See Section 9 in the Introduction to the NAG Library FL Interface for further information.

7 Accuracy

8 Parallelism and Performance

9 Further Comments

10 Example