x10ac_a1w_f sets the computational mode in a configuration data structure for the NAG AD Library as created by a prior call to x10aa_a1w_f. The full set of computational modes currently available are: nagad_algorithmic and nagad_symbolic.

2 Specification

Fortran Interface

Subroutine x10ac_a1w_f (

ad_handle, mode, ifail)

Integer, Intent (In)	::	mode
Integer, Intent (Inout)	::	ifail
Type (c_ptr), Intent (Inout)	::	ad_handle

C++ Header Interface

#include <nagad.h>

extern "C" {

void	x10ac_a1w_f_ (void *&ad_handle, const Integer &mode, Integer &ifail)

}

The routine may be called by the names x10ac_a1w_f or nagf_adutils_config_mode_set_a1w.

3 Description

x10ac_a1w_f sets the computational mode of differentiation in the configuration data object. This handle may then be passed to any computational routine in the NAG AD Library as listed in the Introduction to the NAG AD Library. The computational mode can be changed between calls to computational routines in the NAG AD Library. The computational modes currently available are nagad_algorithmic and nagad_symbolic. See mode. This routine must be called after a call to x10aa_a1w_f (to create a handle to the configuration data object) and prior to the call of the computational NAG AD Library routines for which the mode is set.

3.1 Life Cycle of the Handle

Each handle should pass four stages in its life: initialization; mode setting; problem solution using the NAG AD Library; and, destruction.

The initialization by x10aa_a1w_f and destruction by x10ab_a1w_f mark the beginning and the end of the life of the handle. During this time the handle must only be modified by NAG AD Library routines. Working with a handle which has not been properly initialized is potentially very dangerous as it may cause unpredictable behaviour.

After the handle has been initialized, two routines are provided to set or get the computational mode to be used in algorithmic differentiation. x10ac_a1w_f sets the computational mode and x10ad_a1w_f gets the computational mode.

The handle is then passed to the computational routines of the NAG AD Library. The computational mode can be changed, where appropriate, between calls to computational routines.

When all AD computation is completed, the handle must be destroyed by x10ab_a1w_f.

4 References

None.

5 Arguments

1: $ad_handle$ – Type (c_ptr) Input/Output: On entry: a handle to the AD configuration data object, as created by x10aa_a1w_f.

On exit: holds a handle to the internal data structure where the computational mode was changed according to mode. You must not change the handle other than via NAG AD Library calls until it is destroyed by x10ab_a1w_f.
2: $mode$ – Integer Input: On entry: the computational mode to be used in subsequent calls to NAG AD Library computational routines.
The mode nag_algorithmic is available to all computational routines; this means that differentiation of the primal algorithm (e.g., calculating adjoints) is performed by code, converted and instrumented from the primal code.

The mode nag_symbolic is only available for the subset of computational routines listed in Section 3.2.2 in the X10 Chapter Introduction; these have been hand-coded using knowledge of the differentials of the primal algorithm.

Constraint: $mode = nag_algorithmic$ or $nag_symbolic$ .
3: $ifail$ – Integer Input/Output: On entry: ifail must be set to $0$ , $- 1 or 1$ . If you are unfamiliar with this argument you should refer to Section 4 in the Introduction to the NAG Library FL Interface for details.
For environments where it might be inappropriate to halt program execution when an error is detected, the value $- 1 or 1$ is recommended. If the output of error messages is undesirable, then the value $1$ is recommended. Otherwise, if you are not familiar with this argument, the recommended value is $0$ . When the value $- 1 or 1$ is used it is essential to test the value of ifail on exit.

On exit: $ifail = 0$ unless the routine detects an error or a warning has been flagged (see Section 6).

6 Error Indicators and Warnings

If on entry

ifail = 0

- 1

, explanatory error messages are output on the current error message unit (as defined by x04aaf).

Errors or warnings detected by the routine:

$ifail = 1$: On entry: ad_handle is not a valid handle for the AD computational data object. Either ad_handle has not been initialized or it has become corrupted.

$ifail = 2$: On entry, $mode = 〈value〉$ .
Constraint: $mode = nag_algorithmic$ or $nag_symbolic$ .

$ifail = - 99$: An unexpected error has been triggered by this routine. Please contact NAG.
See Section 7 in the Introduction to the NAG Library FL Interface for further information.

$ifail = - 399$: Your licence key may have expired or may not have been installed correctly.
See Section 8 in the Introduction to the NAG Library FL Interface for further information.

$ifail = - 999$: Dynamic memory allocation failed.
See Section 9 in the Introduction to the NAG Library FL Interface for further information.

7 Accuracy

Not applicable.

8 Parallelism and Performance

x10ac_a1w_f is not threaded in any implementation.

9 Further Comments

None.

10 Example

See examples for computational routines in the NAG AD Library, for example, Section 10 in c05ay_a1w_f.

NAG Library Manual, Mark 27

Interfaces: FL CL AD

NAG AD Interface Introduction

X10 (Adutils) Chapter Contents

X10 (Adutils) Chapter Introduction

x10ac: FL CL AD

NAG AD Libraryx10ac_a1w_f (config_​mode_​set_a1w)

▸▿ Contents

1 Purpose