f11jqf solves a complex sparse Hermitian system of linear equations, represented in symmetric coordinate storage format, using a conjugate gradient or Lanczos method, with incomplete Cholesky preconditioning.
The routine may be called by the names f11jqf or nagf_sparse_complex_herm_solve_ilu.
f11jqf solves a complex sparse Hermitian linear system of equations
using a preconditioned conjugate gradient method (see Meijerink and Van der Vorst (1977)), or a preconditioned Lanczos method based on the algorithm SYMMLQ (see Paige and Saunders (1975)). The conjugate gradient method is more efficient if is positive definite, but may fail to converge for indefinite matrices. In this case the Lanczos method should be used instead. For further details see Barrett et al. (1994).
f11jqf uses the incomplete Cholesky factorization determined by f11jnf as the preconditioning matrix. A call to f11jqf must always be preceded by a call to f11jnf. Alternative preconditioners for the same storage scheme are available by calling f11jsf.
The matrix and the preconditioning matrix are represented in symmetric coordinate storage (SCS) format (see Section 2.1.2 in the F11 Chapter Introduction) in the arrays a, irow and icol, as returned from f11jnf. The array a holds the nonzero entries in the lower triangular parts of these matrices, while irow and icol hold the corresponding row and column indices.
Barrett R, Berry M, Chan T F, Demmel J, Donato J, Dongarra J, Eijkhout V, Pozo R, Romine C and Van der Vorst H (1994) Templates for the Solution of Linear Systems: Building Blocks for Iterative Methods SIAM, Philadelphia
Meijerink J and Van der Vorst H (1977) An iterative solution method for linear systems of which the coefficient matrix is a symmetric M-matrix Math. Comput.31 148–162
Paige C C and Saunders M A (1975) Solution of sparse indefinite systems of linear equations SIAM J. Numer. Anal.12 617–629
1: – Character(*)Input
On entry: specifies the iterative method to be used.
Conjugate gradient method.
Lanczos method (SYMMLQ).
2: – IntegerInput
On entry: , the order of the matrix . This must be the same value as was supplied in the preceding call to f11jnf.
3: – IntegerInput
On entry: the number of nonzero elements in the lower triangular part of the matrix . This must be the same value as was supplied in the preceding call to f11jnf.
4: – Complex (Kind=nag_wp) arrayInput
On entry: the values returned in the array a by a previous call to f11jnf.
5: – IntegerInput
On entry: the dimension of the arrays a, irow and icol as declared in the (sub)program from which f11jqf is called. This must be the same value as was supplied in the preceding call to f11jnf.
On entry: the required tolerance. Let denote the approximate solution at iteration , and the corresponding residual. The algorithm is considered to have converged at iteration if
If , is used, where is the machine precision. Otherwise is used.
12: – IntegerInput
On entry: the maximum number of iterations allowed.
13: – Complex (Kind=nag_wp) arrayInput/Output
On entry: an initial approximation to the solution vector .
On exit: an improved approximation to the solution vector .
14: – Real (Kind=nag_wp)Output
On exit: the final value of the residual norm , where is the output value of itn.
15: – IntegerOutput
On exit: the number of iterations carried out.
16: – Complex (Kind=nag_wp) arrayWorkspace
17: – IntegerInput
On entry: the dimension of the array work as declared in the (sub)program from which f11jqf is called.
if , ;
if , .
18: – IntegerInput/Output
On entry: ifail must be set to , or to set behaviour on detection of an error; these values have no effect when no error is detected.
A value of causes the printing of an error message and program execution will be halted; otherwise program execution continues. A value of means that an error message is printed while a value of means that it is not.
If halting is not appropriate, the value or is recommended. If message printing is undesirable, then the value is recommended. Otherwise, the value is recommended. When the value or is used it is essential to test the value of ifail on exit.
On exit: unless the routine detects an error or a warning has been flagged (see Section 6).
6Error Indicators and Warnings
If on entry or , explanatory error messages are output on the current error message unit (as defined by x04aaf).
Errors or warnings detected by the routine:
On entry, and .
On entry, lwork is too small: . Minimum required value of .
On entry, .
On entry, .
Constraint: or .
On entry, .
On entry, .
On entry, and .
On entry, .
On entry, is out of order: .
On entry, , , . Constraint: and .
On entry, , and . Constraint: and .
On entry, the location () is a duplicate: .
Check that the call to f11jqf has been preceded by a valid call to f11jnf, and that the arrays a, irow, and icol have not been corrupted between the two calls.
The required accuracy could not be obtained. However a reasonable accuracy has been achieved.
The solution has not converged after iterations.
The preconditioner appears not to be positive definite. The computation cannot continue.
The matrix of the coefficients a appears not to be positive definite. The computation cannot continue.
A serious error, code , has occurred in an internal call. Check all subroutine calls and array sizes. Seek expert help.
An unexpected error has been triggered by this routine. Please
See Section 7 in the Introduction to the NAG Library FL Interface for further information.
Your licence key may have expired or may not have been installed correctly.
See Section 8 in the Introduction to the NAG Library FL Interface for further information.
Dynamic memory allocation failed.
See Section 9 in the Introduction to the NAG Library FL Interface for further information.
On successful termination, the final residual , where , satisfies the termination criterion
The value of the final residual norm is returned in rnorm.
8Parallelism and Performance
f11jqf is threaded by NAG for parallel execution in multithreaded implementations of the NAG Library.
f11jqf makes calls to BLAS and/or LAPACK routines, which may be threaded within the vendor library used by this implementation. Consult the documentation for the vendor library for further information.
Please consult the X06 Chapter Introduction for information on how to control and interrogate the OpenMP environment used within this routine. Please also consult the Users' Note for your implementation for any additional implementation-specific information.
The time taken by f11jqf for each iteration is roughly proportional to the value of nnzc returned from the preceding call to f11jnf. One iteration with the Lanczos method (SYMMLQ) requires a slightly larger number of operations than one iteration with the conjugate gradient method.
The number of iterations required to achieve a prescribed accuracy cannot easily be determined a priori, as it can depend dramatically on the conditioning and spectrum of the preconditioned matrix of the coefficients .
This example solves a complex sparse Hermitian positive definite system of equations using the conjugate gradient method, with incomplete Cholesky preconditioning.