NAG Library Routine Document

D02GAF

▸▿ Contents

1 Purpose

2 Specification

3 Description

4 References

5 Parameters

6 Error Indicators and Warnings

7 Accuracy

8 Parallelism and Performance

9 Further Comments

▸▿ 10 Example

10.1 Program Text

10.2 Program Data

10.3 Program Results

1 Purpose

D02GAF solves a two-point boundary value problem with assigned boundary values for a system of ordinary differential equations, using a deferred correction technique and a Newton iteration.

2 Specification

SUBROUTINE D02GAF (

U, V, N, A, B, TOL, FCN, MNP, X, Y, NP, W, LW, IW, LIW, IFAIL)

INTEGER	N, MNP, NP, LW, IW(LIW), LIW, IFAIL
REAL (KIND=nag_wp)	U(N,2), V(N,2), A, B, TOL, X(MNP), Y(N,MNP), W(LW)
EXTERNAL	FCN

3 Description

D02GAF solves a two-point boundary value problem for a system of

n

differential equations in the interval [

a, b

]. The system is written in the form:

y_{i}^{'} = f_{i} (x, y_{1}, y_{2}, \dots, y_{n}), i = 1, 2, \dots, n

(1)

and the derivatives

f_{i}

are evaluated by FCN. Initially,

n

boundary values of the variables

y_{i}

must be specified, some at

a

and some at

b

. You must supply estimates of the remaining

n

boundary values and all the boundary values are used in constructing an initial approximation to the solution. This approximate solution is corrected by a finite difference technique with deferred correction allied with a Newton iteration to solve the finite difference equations. The technique used is described fully in Pereyra (1979). The Newton iteration requires a Jacobian matrix

\frac{\partial f_{i}}{\partial y_{j}}

and this is calculated by numerical differentiation using an algorithm described in Curtis et al. (1974).

You supply an absolute error tolerance and may also supply an initial mesh for the construction of the finite difference equations (alternatively a default mesh is used). The algorithm constructs a solution on a mesh defined by adding points to the initial mesh. This solution is chosen so that the error is everywhere less than your tolerance and so that the error is approximately equidistributed on the final mesh. The solution is returned on this final mesh.

If the solution is required at a few specific points then these should be included in the initial mesh. If on the other hand the solution is required at several specific points then you should use the interpolation routines provided in Chapter E01 if these points do not themselves form a convenient mesh.

4 References

Curtis A R, Powell M J D and Reid J K (1974) On the estimation of sparse Jacobian matrices J. Inst. Maths. Applics. 13 117–119

Pereyra V (1979) PASVA3: An adaptive finite-difference Fortran program for first order nonlinear, ordinary boundary problems Codes for Boundary Value Problems in Ordinary Differential Equations. Lecture Notes in Computer Science (eds B Childs, M Scott, J W Daniel, E Denman and P Nelson) 76 Springer–Verlag

5 Parameters

1: $U (N, 2)$ – REAL (KIND=nag_wp) arrayInput

On entry:

U (i, 1)

must be set to the known or estimated value of

y_{i}

a

and

U (i, 2)

must be set to the known or estimated value of

y_{i}

b

, for

i = 1, 2, \dots, n

2: $V (N, 2)$ – REAL (KIND=nag_wp) arrayInput

On entry:

V (i, j)

must be set to

0.0

U (i, j)

is a known value and to

1.0

U (i, j)

is an estimated value, for

i = 1, 2, \dots, n

and

j = 1, 2

Constraint: precisely

n

of the

V (i, j)

must be set to

0.0

, i.e., precisely

n

of the

U (i, j)

must be known values, and these must not be all at

a

or all at

b

3: $N$ – INTEGERInput

On entry:

n

, the number of equations.

Constraint:

N \geq 2

4: $A$ – REAL (KIND=nag_wp)Input

On entry:

a

, the left-hand boundary point.

5: $B$ – REAL (KIND=nag_wp)Input

On entry:

b

, the right-hand boundary point.

Constraint:

B > A

6: $TOL$ – REAL (KIND=nag_wp)Input

On entry: a positive absolute error tolerance. If

a = x_{1} < x_{2} < \dots < x_{NP} = b

is the final mesh,

z_{j} (x_{i})

is the

j

th component of the approximate solution at

x_{i}

, and

y_{j} (x)

is the

j

th component of the true solution of equation (1) (see Section 3) and the boundary conditions, then, except in extreme cases, it is expected that

|z_{j} (x_{i}) - y_{j} (x_{i})| \leq TOL, i = 1, 2, \dots, NP ​ and ​ j = 1, 2, \dots, n .

(2)

Constraint:

TOL > 0.0

7: $FCN$ – SUBROUTINE, supplied by the user.External Procedure

FCN must evaluate the functions

f_{i}

(i.e., the derivatives

y_{i}^{'}

), for

i = 1, 2, \dots, n

, at a general point

x

The specification of FCN is:

SUBROUTINE FCN (

X, Y, F)

REAL (KIND=nag_wp)

X, Y(*), F(*)

In the description of the parameters of D02GAF below,

n

denotes the actual value of N in the call of D02GAF.

1: $X$ – REAL (KIND=nag_wp)Input: On entry: $x$ , the value of the argument.
2: $Y (*)$ – REAL (KIND=nag_wp) arrayInput: On entry: $y_{i}$ , for $i = 1, 2, \dots, n$ , the value of the argument.
3: $F (*)$ – REAL (KIND=nag_wp) arrayOutput: On exit: the values of $f_{i}$ , for $i = 1, 2, \dots, n$ .

FCN must either be a module subprogram USEd by, or declared as EXTERNAL in, the (sub)program from which D02GAF is called. Parameters denoted as Input must not be changed by this procedure.

8: $MNP$ – INTEGERInput

On entry: the maximum permitted number of mesh points.

Constraint:

MNP \geq 32

9: $X (MNP)$ – REAL (KIND=nag_wp) arrayInput/Output

On entry: if

NP \geq 4

(see NP), the first NP elements must define an initial mesh. Otherwise the elements of X need not be set.

Constraint:

A = X (1) < X (2) < \dots < X (NP) = B, NP \geq 4 .

(3)

On exit:

X (1), X (2), \dots, X (NP)

define the final mesh (with the returned value of NP) satisfying the relation (3).

10: $Y (N, MNP)$ – REAL (KIND=nag_wp) arrayOutput

On exit: the approximate solution

z_{j} (x_{i})

satisfying (2), on the final mesh, that is

Y (j, i) = z_{j} (x_{i}), i = 1, 2, \dots, NP ​ and ​ j = 1, 2, \dots, n,

where NP is the number of points in the final mesh.

The remaining columns of Y are not used.

11: $NP$ – INTEGERInput/Output

On entry: determines whether a default or user-supplied mesh is used.

$NP = 0$: A default value of $4$ for NP and a corresponding equispaced mesh $X (1), X (2), \dots, X (NP)$ are used.
$NP \geq 4$: You must define an initial mesh using the array X as described.

Constraint:

NP = 0

4 \leq NP \leq MNP

On exit: the number of points in the final (returned) mesh.

12: $W (LW)$ – REAL (KIND=nag_wp) arrayWorkspace

13: $LW$ – INTEGERInput

On entry: the dimension of the array W as declared in the (sub)program from which D02GAF is called.

Constraint:

LW \geq MNP \times (3 N^{2} + 6 N + 2) + 4 N^{2} + 4 N

14: $IW (LIW)$ – INTEGER arrayWorkspace

15: $LIW$ – INTEGERInput

On entry: the dimension of the array IW as declared in the (sub)program from which D02GAF is called.

Constraint:

LIW \geq MNP \times (2 N + 1) + N^{2} + 4 N + 2

16: $IFAIL$ – INTEGERInput/Output

For this routine, the normal use of IFAIL is extended to control the printing of error and warning messages as well as specifying hard or soft failure (see Section 3.3 in the Essential Introduction).

On entry: IFAIL must be set to a value with the decimal expansion

cba

, where each of the decimal digits

c

b

and

a

must have a value of

0

1

$a = 0$	specifies hard failure, otherwise soft failure;
$b = 0$	suppresses error messages, otherwise error messages will be printed (see Section 6);
$c = 0$	suppresses warning messages, otherwise warning messages will be printed (see Section 6).

The recommended value for inexperienced users is

110

(i.e., hard failure with all messages printed).

On exit:

IFAIL = 0

unless the routine detects an error or a warning has been flagged (see Section 6).

6 Error Indicators and Warnings

If on entry

IFAIL = 0

- 1

, explanatory error messages are output on the current error message unit (as defined by X04AAF).

Errors or warnings detected by the routine:

$IFAIL = 1$: One or more of the parameters N, TOL, NP, MNP, LW or LIW has been incorrectly set, or $B \leq A$ , or the condition (3) on X is not satisfied, or the number of known boundary values (specified by V) is not N.

$IFAIL = 2$: The Newton iteration has failed to converge. This could be due to there being too few points in the initial mesh or to the initial approximate solution being too inaccurate. If this latter reason is suspected you should use D02RAF instead. If the warning ‘Jacobian matrix is singular’ is printed this could be due to specifying zero estimated boundary values and these should be varied. This warning could also be printed in the unlikely event of the Jacobian matrix being calculated inaccurately. If you cannot make changes to prevent the warning then D02RAF should be used.

$IFAIL = 3$: The Newton iteration has reached round-off level. It could be, however, that the answer returned is satisfactory. This error might occur if too much accuracy is requested.

$IFAIL = 4$: A finer mesh is required for the accuracy requested; that is MNP is not large enough.

$IFAIL = 5$: A serious error has occurred in a call to D02GAF. Check all array subscripts and subroutine parameter lists in calls to D02GAF. Seek expert help.

$IFAIL = - 99$: An unexpected error has been triggered by this routine. Please contact NAG.
See Section 3.8 in the Essential Introduction for further information.

$IFAIL = - 399$: Your licence key may have expired or may not have been installed correctly.
See Section 3.7 in the Essential Introduction for further information.

$IFAIL = - 999$: Dynamic memory allocation failed.
See Section 3.6 in the Essential Introduction for further information.

7 Accuracy

The solution returned by the routine will be accurate to your tolerance as defined by the relation (2) except in extreme circumstances. If too many points are specified in the initial mesh, the solution may be more accurate than requested and the error may not be approximately equidistributed.

8 Parallelism and Performance

Not applicable.

9 Further Comments

The time taken by D02GAF depends on the difficulty of the problem, the number of mesh points (and meshes) used, the number of Newton iterations and the number of deferred corrections.

You are strongly recommended to set IFAIL to obtain self-explanatory error messages, and also monitoring information about the course of the computation. You may select the unit numbers on which this output is to appear by calls of X04AAF (for error messages) or X04ABF (for monitoring information) – see Section 10 for an example. Otherwise the default unit numbers will be used, as specified in the Users' Note.

A common cause of convergence problems in the Newton iteration is that you have specified too few points in the initial mesh. Although the routine adds points to the mesh to improve accuracy it is unable to do so until the solution on the initial mesh has been calculated in the Newton iteration.

If you specify zero known and estimated boundary values, the routine constructs a zero initial approximation and in many cases the Jacobian is singular when evaluated for this approximation, leading to the breakdown of the Newton iteration.

You may be unable to provide a sufficiently good choice of initial mesh and estimated boundary values, and hence the Newton iteration may never converge. In this case the continuation facility provided in D02RAF is recommended.

In the case where you wish to solve a sequence of similar problems, the final mesh from solving one case is strongly recommended as the initial mesh for the next.

10 Example

This example solves the differential equation

y^{'''} = - y y^{''} - β (1 - {y^{'}}^{2})

with boundary conditions

y (0) = y^{'} (0) = 0, y^{'} (10) = 1

for

β = 0.0

and

β = 0.2

to an accuracy specified by

TOL = 1.0E−3

. We solve first the simpler problem with

β = 0.0

using an equispaced mesh of

26

points and then we solve the problem with

β = 0.2

using the final mesh from the first problem.

Note the call to X04ABF prior to the call to D02GAF.

NAG Library Routine DocumentD02GAF

▸▿ Contents

1 Purpose

2 Specification

3 Description

4 References

5 Parameters

6 Error Indicators and Warnings

7 Accuracy

8 Parallelism and Performance

9 Further Comments

10 Example

10.1 Program Text

10.2 Program Data

10.3 Program Results

NAG Library Routine Document

D02GAF