NAG Library Routine Document

e01zmf generates a multidimensional interpolant to a set of scattered data points, using a modified Shepard method. When the number of dimensions is no more than five, there are corresponding routines in Chapter E01 which are specific to the given dimensionality. e01sgf generates the two-dimensional interpolant, while e01tgf, e01tkf and e01tmf generate the three-, four- and five-dimensional interpolants respectively.

2

Specification

Fortran Interface

Subroutine e01zmf (

d, m, x, f, nw, nq, iq, rq, ifail)

Integer, Intent (In)	::	d, m, nw, nq
Integer, Intent (Inout)	::	ifail
Integer, Intent (Out)	::	iq(2*m+1)
Real (Kind=nag_wp), Intent (In)	::	x(d,m), f(m)
Real (Kind=nag_wp), Intent (Out)	::	rq(*)

C Header Interface

#include <nagmk26.h>

void	e01zmf_ (const Integer d, const Integer m, const double x[], const double f[], const Integer nw, const Integer nq, Integer iq[], double rq[], Integer *ifail)

3

Description

e01zmf constructs a smooth function

Q (x)

x \in ℝ^{d}

which interpolates a set of

m

scattered data points

(x_{r}, f_{r})

, for

r = 1, 2, \dots, m

, using a modification of Shepard's method. The surface is continuous and has continuous first partial derivatives.

The basic Shepard method, which is a generalization of the two-dimensional method described in Shepard (1968), interpolates the input data with the weighted mean

Q (x) = \frac{\sum_{r = 1}^{m} w_{r} (x) q_{r}}{\sum_{r = 1}^{m} w_{r} (x)},

where

q_{r} = f_{r}

w_{r} (x) = \frac{1}{{‖x - x_{r}‖}_{2}^{2}}

The basic method is global in that the interpolated value at any point depends on all the data, but e01zmf uses a modification (see Franke and Nielson (1980) and Renka (1988a)), whereby the method becomes local by adjusting each

w_{r} (x)

to be zero outside a hypersphere with centre

x_{r}

and some radius

R_{w}

. Also, to improve the performance of the basic method, each

q_{r}

above is replaced by a function

q_{r} (x)

, which is a quadratic fitted by weighted least squares to data local to

x_{r}

and forced to interpolate

(x_{r}, f_{r})

. In this context, a point

x

is defined to be local to another point if it lies within some distance

R_{q}

of it.

The efficiency of e01zmf is enhanced by using a cell method for nearest neighbour searching due to Bentley and Friedman (1979) with a cell density of

3

The radii

R_{w}

and

R_{q}

are chosen to be just large enough to include

N_{w}

and

N_{q}

data points, respectively, for user-supplied constants

N_{w}

and

N_{q}

. Default values of these parameters are provided, and advice on alternatives is given in Section 9.2.

e01zmf is derived from the new implementation of QSHEP3 described by Renka (1988b). It uses the modification for high-dimensional interpolation described by Berry and Minser (1999).

Values of the interpolant

Q (x)

generated by e01zmf, and its first partial derivatives, can subsequently be evaluated for points in the domain of the data by a call to e01znf.

4

References

Bentley J L and Friedman J H (1979) Data structures for range searching ACM Comput. Surv. 11 397–409

Berry M W, Minser K S (1999) Algorithm 798: high-dimensional interpolation using the modified Shepard method ACM Trans. Math. Software 25 353–366

Franke R and Nielson G (1980) Smooth interpolation of large sets of scattered data Internat. J. Num. Methods Engrg. 15 1691–1704

Renka R J (1988a) Multivariate interpolation of large sets of scattered data ACM Trans. Math. Software 14 139–148

Renka R J (1988b) Algorithm 661: QSHEP3D: Quadratic Shepard method for trivariate interpolation of scattered data ACM Trans. Math. Software 14 151–152

Shepard D (1968) A two-dimensional interpolation function for irregularly spaced data Proc. 23rd Nat. Conf. ACM 517–523 Brandon/Systems Press Inc., Princeton

5

Arguments

1: $d$ – IntegerInput: On entry: $d$ , the number of dimensions.

Constraint: $d \geq 2$ .
2: $m$ – IntegerInput: On entry: $m$ , the number of data points.
Note: on the basis of experimental results reported in Berry and Minser (1999), when $d \geq 5$ it is recommended to use $m \geq 4000$ .

Constraint: $m \geq (d + 1) \times (d + 2) / 2 + 2$ .
3: $x (d, m)$ – Real (Kind=nag_wp) arrayInput: On entry: $x (1 : d, r)$ must be set to the Cartesian coordinates of the data point $x_{r}$ , for $r = 1, 2, \dots, m$ .

Constraint: these coordinates must be distinct, and must not all lie on the same $(d - 1)$ -dimensional hypersurface.
4: $f (m)$ – Real (Kind=nag_wp) arrayInput: On entry: $f (r)$ must be set to the data value $f_{r}$ , for $r = 1, 2, \dots, m$ .
5: $nw$ – IntegerInput: On entry: the number $N_{w}$ of data points that determines each radius of influence $R_{w}$ , appearing in the definition of each of the weights $w_{r}$ , for $r = 1, 2, \dots, m$ (see Section 3). Note that $R_{w}$ is different for each weight. If $nw \leq 0$ the default value $nw = \min (2 \times (d + 1) \times (d + 2), m - 1)$ is used instead.

Suggested value: $nw = - 1$ .

Constraint: $nw \leq m - 1$ .
6: $nq$ – IntegerInput: On entry: the number $N_{q}$ of data points to be used in the least squares fit for coefficients defining the quadratic functions $q_{r} (x)$ (see Section 3). If $nq \leq 0$ the default value $nq = \min ((d + 1) \times (d + 2) \times 6 / 5, m - 1)$ is used instead.

Suggested value: $nq = - 1$ .

Constraint: $nq \leq 0$ or $(d + 1) \times (d + 2) / 2 - 1 \leq nq \leq m - 1$ .
7: $iq (2 \times m + 1)$ – Integer arrayOutput: On exit: integer data defining the interpolant $Q (x)$ .
8: $rq (*)$ – Real (Kind=nag_wp) arrayOutput: Note: the dimension of the array rq must be at least $((d + 1) \times (d + 2) / 2) \times m + 2 \times d + 1$ .

On exit: real data defining the interpolant $Q (x)$ .
9: $ifail$ – IntegerInput/Output: On entry: ifail must be set to $0$ , $- 1 or 1$ . If you are unfamiliar with this argument you should refer to Section 3.4 in How to Use the NAG Library and its Documentation for details.
For environments where it might be inappropriate to halt program execution when an error is detected, the value $- 1 or 1$ is recommended. If the output of error messages is undesirable, then the value $1$ is recommended. Otherwise, if you are not familiar with this argument, the recommended value is $0$ . When the value $- 1 or 1$ is used it is essential to test the value of ifail on exit.

On exit: $ifail = 0$ unless the routine detects an error or a warning has been flagged (see Section 6).

6

Error Indicators and Warnings

If on entry

ifail = 0

- 1

, explanatory error messages are output on the current error message unit (as defined by x04aaf).

Errors or warnings detected by the routine:

$ifail = 1$: On entry, $d = 〈value〉$ .
Constraint: $d \geq 2$ .

On entry, $((d + 1) \times (d + 2) / 2) \times m + 2 \times d + 1$ exceeds the largest machine integer.
$d = 〈value〉$ and $m = 〈value〉$ .

On entry, $m = 〈value〉$ and $d = 〈value〉$ .
Constraint: $m \geq (d + 1) \times (d + 2) / 2 + 2$ .

On entry, $nq = 〈value〉$ and $d = 〈value〉$ .
Constraint: $nq \leq 0$ or $nq \geq (d + 1) \times (d + 2) / 2 - 1$ .

On entry, $nq = 〈value〉$ and $m = 〈value〉$ .
Constraint: $nq \leq m - 1$ .

On entry, $nw = 〈value〉$ and $m = 〈value〉$ .
Constraint: $nw \leq m - 1$ .

$ifail = 2$: There are duplicate nodes in the dataset. $x (k, i) = x (k, j)$ , for $i = 〈value〉$ , $j = 〈value〉$ and $k = 1, 2, \dots, d$ . The interpolant cannot be derived.

$ifail = 3$: On entry, all the data points lie on the same hypersurface. No unique solution exists.

$ifail = - 99$: An unexpected error has been triggered by this routine. Please contact NAG.
See Section 3.9 in How to Use the NAG Library and its Documentation for further information.

$ifail = - 399$: Your licence key may have expired or may not have been installed correctly.
See Section 3.8 in How to Use the NAG Library and its Documentation for further information.

$ifail = - 999$: Dynamic memory allocation failed.
See Section 3.7 in How to Use the NAG Library and its Documentation for further information.

7

Accuracy

In experiments undertaken by Berry and Minser (1999), the accuracies obtained for a conditional function resulting in sharp functional transitions were of the order of

10^{- 1}

at best. In other cases in these experiments, the function generated interpolates the input data with maximum absolute error of the order of

10^{- 2}

8

Parallelism and Performance

e01zmf is threaded by NAG for parallel execution in multithreaded implementations of the NAG Library.

e01zmf makes calls to BLAS and/or LAPACK routines, which may be threaded within the vendor library used by this implementation. Consult the documentation for the vendor library for further information.

Please consult the X06 Chapter Introduction for information on how to control and interrogate the OpenMP environment used within this routine. Please also consult the Users' Note for your implementation for any additional implementation-specific information.

9

Further Comments

9.1

Timing

The time taken for a call to e01zmf will depend in general on the distribution of the data points and on the choice of

N_{w}

and

N_{q}

parameters. If the data points are uniformly randomly distributed, then the time taken should be

O (m)

. At worst

O (m^{2})

time will be required.

9.2

Choice of $N_{w}$ and $N_{q}$

Default values of the parameters

N_{w}

and

N_{q}

may be selected by calling e01zmf with

nw \leq 0

and

nq \leq 0

. These default values may well be satisfactory for many applications.

If non-default values are required they must be supplied to e01zmf through positive values of nw and nq. Increasing these argument values makes the method less local. This may increase the accuracy of the resulting interpolant at the expense of increased computational cost. The default values

nw = \min (2 \times (d + 1) \times (d + 2), m - 1)

and

nq = \min ((d + 1) \times (d + 2) \times 6 / 5, m - 1)

have been chosen on the basis of experimental results reported in Renka (1988a) and Berry and Minser (1999). For further advice on the choice of these arguments see Renka (1988a) and Berry and Minser (1999).

9.3

Internal Changes

Internal changes have been made to this routine as follows:

At Mark 26.0: The algorithm used by this routine, based on a Modified Shepard method, has been changed to produce more reliable results for some data sets which were previously not well handled. In addition, handling of evaluation points which are far away from the original data points has been improved by use of an extrapolation method which returns useful results rather than just an error message as was done at earlier Marks.
At Mark 26.1: The algorithm has undergone further changes which enable it to work better on certain data sets, for example data presented on a regular grid. The results returned when evaluating the function at points which are not in the original data set used to construct the interpolating function are now likely to be slightly different from those returned at previous Marks of the Library, but the function still interpolates the original data.

For details of all known issues which have been reported for the NAG Library please refer to the Known Issues list.

10

Example

This program reads in a set of

30

data points and calls e01zmf to construct an interpolating function

Q (x)

. It then calls e01znf to evaluate the interpolant at a set of points.

Note that this example is not typical of a realistic problem: the number of data points would normally be very much larger.

NAG Library Routine Document

e01zmf (dimn_scat_shep)

▸▿ Contents

1 Purpose

2 Specification

3 Description

4 References

5 Arguments

6 Error Indicators and Warnings

7 Accuracy

8 Parallelism and Performance

9 Further Comments

9.1 Timing

9.2 Choice of Nw and Nq

9.3 Internal Changes

10 Example

10.1 Program Text

10.2 Program Data

10.3 Program Results

1

Purpose