G01ALF (PDF version)
G01 Chapter Contents
G01 Chapter Introduction
NAG Library Manual

NAG Library Routine Document


Note:  before using this routine, please read the Users' Note for your implementation to check the interpretation of bold italicised terms and other implementation-dependent details.


    1  Purpose
    7  Accuracy

1  Purpose

G01ALF calculates a five-point summary for a single sample.

2  Specification

REAL (KIND=nag_wp)  X(N), RES(5)

3  Description

G01ALF calculates the minimum, lower hinge, median, upper hinge and the maximum of a sample of n observations.
The data consist of a single sample of n observations denoted by xi and let zi, for i=1,2,,n, represent the sample observations sorted into ascending order.
Let m= n2  if n is even and n+1 2  if n is odd,
and k= m2  if m is even and m+1 2  if m is odd.
Then we have
Minimum =z1,  
Maximum =zn,  
Median =zm if n is odd,
  = zm+zm+12 if n is even, 12
Lower hinge =zk if m is odd,
  = zk+zk+12 if m is even, 12
Upper hinge =zn-k+1 if m is odd,
  = zn-k+zn-k+12 if m is even. 12

4  References

Erickson B H and Nosanchuk T A (1985) Understanding Data Open University Press, Milton Keynes
Tukey J W (1977) Exploratory Data Analysis Addison–Wesley

5  Parameters

1:     N – INTEGERInput
On entry: n, number of observations in the sample.
Constraint: N5.
2:     XN – REAL (KIND=nag_wp) arrayInput
On entry: the sample observations, x1,x2,,xn.
3:     IWRKN – INTEGER arrayWorkspace
4:     RES5 – REAL (KIND=nag_wp) arrayOutput
On exit: RES contains the five-point summary.
The minimum.
The lower hinge.
The median.
The upper hinge.
The maximum.
5:     IFAIL – INTEGERInput/Output
On entry: IFAIL must be set to 0, -1​ or ​1. If you are unfamiliar with this parameter you should refer to Section 3.3 in the Essential Introduction for details.
For environments where it might be inappropriate to halt program execution when an error is detected, the value -1​ or ​1 is recommended. If the output of error messages is undesirable, then the value 1 is recommended. Otherwise, if you are not familiar with this parameter, the recommended value is 0. When the value -1​ or ​1 is used it is essential to test the value of IFAIL on exit.
On exit: IFAIL=0 unless the routine detects an error or a warning has been flagged (see Section 6).

6  Error Indicators and Warnings

If on entry IFAIL=0 or -1, explanatory error messages are output on the current error message unit (as defined by X04AAF).
Errors or warnings detected by the routine:
On entry,N<5.
An unexpected error has been triggered by this routine. Please contact NAG.
See Section 3.8 in the Essential Introduction for further information.
Your licence key may have expired or may not have been installed correctly.
See Section 3.7 in the Essential Introduction for further information.
Dynamic memory allocation failed.
See Section 3.6 in the Essential Introduction for further information.

7  Accuracy

The computations are stable.

8  Parallelism and Performance

Not applicable.

9  Further Comments

The time taken by G01ALF is proportional to n.

10  Example

This example calculates a five-point summary for a sample of 12 observations.

10.1  Program Text

Program Text (g01alfe.f90)

10.2  Program Data

Program Data (g01alfe.d)

10.3  Program Results

Program Results (g01alfe.r)

G01ALF (PDF version)
G01 Chapter Contents
G01 Chapter Introduction
NAG Library Manual

© The Numerical Algorithms Group Ltd, Oxford, UK. 2015