NAG Library Function Document

nag_transport (h03abc)

void	nag_transport (const double cost[], Integer tdcost, const double avail[], Integer navail, const double req[], Integer nreq, Integer maxit, Integer numit, double optq[], Integer source[], Integer dest[], double optcost, double unitcost[], NagError *fail)

3 Description

nag_transport (h03abc) solves the transportation problem by minimizing

z = \sum_{i}^{m_{a}} \sum_{j}^{m_{b}} c_{i j} x_{i j} .

subject to the constraints

\begin{matrix} \sum_{j}^{m_{b}} x_{i j} = A_{i} & (availabilities) \\ \sum_{i}^{m_{a}} x_{i j} = B_{j} & (requirements) \end{matrix}

where the

x_{i j}

can be interpreted as quantities of goods sent from source

i

to destination

j

, for

i = 1, 2, \dots, m_{a}

and

j = 1, 2, \dots, m_{b}

, at a cost of

c_{i j}

per unit, and it is assumed that

\sum_{i}^{m_{a}} A_{i} = \sum_{j}^{m_{b}} B_{j}

and

x_{i j} \geq 0

nag_transport (h03abc) uses the ‘stepping stone’ method, modified to accept degenerate cases.

4 References

Hadley G (1962) Linear Programming Addison–Wesley

5 Arguments

1: $cost [navail \times tdcost]$ – const doubleInput: On entry: $cost [(i - 1) \times tdcost + j - 1]$ contains the coefficients $c_{i j}$ , for $i = 1, 2, \dots, m_{a}$ and $j = 1, 2, \dots, m_{b}$ .
2: $tdcost$ – IntegerInput: On entry: the stride separating matrix column elements in the array cost.

Constraint: $tdcost \geq nreq$ .
3: $avail [navail]$ – const doubleInput: On entry: $avail [i - 1]$ must be set to the availabilities $A_{i}$ , for $i = 1, 2, \dots, m_{a}$ ;
4: $navail$ – IntegerInput: On entry: the number of sources, $m_{a}$ .

Constraint: $navail \geq 1$ .
5: $req [nreq]$ – const doubleInput: On entry: $req [j - 1]$ must be set to the requirements $B_{j}$ , for $j = 1, 2, \dots, m_{b}$ .
6: $nreq$ – IntegerInput: On entry: the number of destinations, $m_{b}$ .

Constraint: $nreq \geq 1$ .
7: $maxit$ – IntegerInput: On entry: the maximum number of iterations allowed.

Constraint: $maxit \geq 1$ .
8: $numit$ – Integer *Output: On exit: the number of iterations performed.
9: $optq [navail + nreq]$ – doubleOutput: On exit: $optq [k - 1]$ , for $k = 1, 2, \dots, m_{a} + m_{b} - 1$ , contains the optimal quantities $x_{i j}$ which, when sent from source $i = source [k - 1]$ to destination $j = dest [k - 1]$ , minimize $z$ .
10: $source [navail + nreq]$ – IntegerOutput: On exit: $source [k - 1]$ , for $k = 1, 2, \dots, m_{a} + m_{b} - 1$ , contains the source indices of the optimal solution (see optq above).
11: $dest [navail + nreq]$ – IntegerOutput: On exit: $dest [k - 1]$ , for $k = 1, 2, \dots, m_{a} + m_{b} - 1$ , contains the destination indices of the optimal solution (see optq above).
12: $optcost$ – double *Output: On exit: the value of the minimized total cost.
13: $unitcost [navail + nreq]$ – doubleOutput: On exit: $unitcost [k - 1]$ , for $k = 1, 2, \dots, m_{a} + m_{b} - 1$ , contains the unit cost $c_{i j}$ associated with the route from source $i = source [k - 1]$ to destination $j = dest [k - 1]$ .
14: $fail$ – NagError *Input/Output: The NAG error argument (see Section 3.6 in the Essential Introduction).

6 Error Indicators and Warnings

NE_2_INT_ARG_LT: On entry, $tdcost = 〈value〉$ while $nreq = 〈value〉$ . These arguments must satisfy $tdcost \geq nreq$ .
NE_ALLOC_FAIL: Dynamic memory allocation failed.
NE_INT_ARG_LT: On entry, $maxit = 〈value〉$ .
Constraint: $maxit \geq 1$ .

On entry, $navail = 〈value〉$ .
Constraint: $navail \geq 1$ .

On entry, $nreq = 〈value〉$ .
Constraint: $nreq \geq 1$ .
NE_REQ_AVAIL: The relative difference between the sum of availabilities and the sum of requirements is greater than machine precision. relative difference $= 〈value〉$ , $machine precision = 〈value〉$ .
NE_TOO_MANY: Too many iterations ( $〈value〉$ )

7 Accuracy

The computations are stable.

8 Parallelism and Performance

Not applicable.

9 Further Comments

An a priori estimate of the run time for a particular problem is difficult to obtain.

10 Example

A company has three warehouses and three stores. The warehouses have a surplus of 12 units of a given commodity divided between them as follows:

Warehouse	Surplus
1	1
2	5
3	6

The stores altogether need 12 units of commodity, with the following requirements:

Store	Requirement
1	4
2	4
3	4

Costs of shipping one unit of the commodity from warehouse

i

to store

j

are displayed in the following matrix:

		Store
		1	2	3
	1	8	8	11
Warehouse	2	5	8	14
	3	4	3	10

It is required to find the units of commodity to be moved from the warehouses to the stores, such that the transportation costs are minimized. The maximum number of iterations allowed is 200.