NAG Library Routine Document

D02QXF

1  Purpose

2  Specification

3  Description

4  References

5  Parameters

1:     NEQF – INTEGERInput

On entry: the number of first-order ordinary differential equations solved by the integration routine. It must be the same parameter NEQF supplied to the setup routine D02QWF and the integration routines D02QFF or D02QGF.

2:     YP(NEQF) – REAL (KIND=nag_wp) arrayOutput

On exit: the approximate derivative of the solution component $y_i$, as supplied in $y_i$ on output from the integration routine at the output value of T. These values are obtained by the evaluation of $y^{\prime }=f\left(x,y\right)$ except when the output value of the parameter T in the call to the integration routine is TOUT and $\mathbf{TCURR}\ne \mathbf{TOUT}$, in which case they are obtained by interpolation.

3:     TCURR – REAL (KIND=nag_wp)Output

On exit: the value of the independent variable which the integrator has actually reached. TCURR will always be at least as far as the output value of the argument T (from the integration routine) in the direction of integration, but may be further.

4:     HLAST – REAL (KIND=nag_wp)Output

On exit: the last successful step size used by the integrator.

5:     HNEXT – REAL (KIND=nag_wp)Output

On exit: the next step size which the integration routine would attempt.

6:     ODLAST – INTEGEROutput

On exit: the order of the method last used (successfully) by the integration routine.

7:     ODNEXT – INTEGEROutput

On exit: the order of the method which the integration routine would attempt on the next step.

8:     NSUCC – INTEGEROutput

On exit: the number of steps attempted by the integration routine that have been successful since the start of the current problem.

9:     NFAIL – INTEGEROutput

On exit: the number of steps attempted by the integration routine that have failed since the start of the current problem.

10:   TOLFAC – REAL (KIND=nag_wp)Output

On exit: a tolerance scale factor, $\mathbf{TOLFAC}\ge 1.0$, returned when the integration routine exits with $\mathbf{IFAIL}=\mathbf{3}$. If RTOL and ATOL are uniformly scaled up by a factor of TOLFAC and D02QWF is called, the next call to the integration routine is deemed likely to succeed.

11:   BADCMP – INTEGEROutput

On exit: if the integration routine returned with $\mathbf{IFAIL}=\mathbf{4}$, then BADCMP specifies the index of the component which forced the error exit. Otherwise BADCMP is $0$.

12:   RWORK(LRWORK) – REAL (KIND=nag_wp) arrayCommunication Array

On entry: this must be the same parameter RWORK as supplied to D02QFF or D02QGF. It is used to pass information from the integration routine to D02QXF and therefore the contents of this array must not be changed before calling D02QXF.

13:   LRWORK – INTEGERInput

On entry: the dimension of the array RWORK as declared in the (sub)program from which D02QXF is called.

This must be the same parameter LRWORK as supplied to D02QWF.

14:   IWORK(LIWORK) – INTEGER arrayCommunication Array

On entry: this must be the same parameter IWORK as supplied to D02QFF or D02QGF. It is used to pass information from the integration routine to D02QXF and therefore the contents of this array must not be changed before calling D02QXF.

15:   LIWORK – INTEGERInput

On entry: the dimension of the array IWORK as declared in the (sub)program from which D02QXF is called.

This must be the same parameter LIWORK as supplied to D02QWF.

16:   IFAIL – INTEGERInput/Output

On entry: IFAIL must be set to $0$, $-1\text{ or }1$. If you are unfamiliar with this parameter you should refer to Section 3.3 in the Essential Introduction for details.

For environments where it might be inappropriate to halt program execution when an error is detected, the value $-1\text{ or }1$ is recommended. If the output of error messages is undesirable, then the value $1$ is recommended. Otherwise, if you are not familiar with this parameter, the recommended value is $0$. When the value $-\mathbf{1}\text{ or }\mathbf{1}$ is used it is essential to test the value of IFAIL on exit.

On exit: $\mathbf{IFAIL}=\mathbf{0}$ unless the routine detects an error or a warning has been flagged (see Section 6).

6  Error Indicators and Warnings

$\mathbf{IFAIL}=1$

An integration routine (D02QFF or D02QGF) has not been called or one or more of the parameters LRWORK, LIWORK and NEQF does not match the corresponding parameter supplied to D02QWF.

This error exit may be caused by overwriting elements of RWORK.

7  Accuracy

8  Further Comments

9  Example